TIG Welding
Tig Welding Techniques
Dip and Pause along with Lay Wire Tig Welding Techniques - Video shows both
Categories: All Feeds, TIG Welding
Amazing Blaze Welding - If You Dont like the way I do it, I'll let you try it.
My friends call me Amazing Blaze...I'm the owner and operator of Heatin ana Beatin Welding Service
Categories: All Feeds, TIG Welding
80/20 gas mix??
I have a miller 212 that I always run 75/25 in. Today I want to get another tank and all the store had was a 80/20 mix. What is the difference in the weld
Categories: All Feeds, TIG Welding
Mig Stainless Steel Settings
I'm practicing welding stainless steel panels 16 ga with .030 308 wire. When I'm tuning in the settings its strange. It's a slow short circuit transfer.
Categories: All Feeds, TIG Welding
Embedded in China
I have been using a Shanhai Soyi NBC 250T now for about 2 years. Since I work here in China, I really had no choice but to buy a machine manufactured here.
Categories: All Feeds, TIG Welding
I bought a Lotus ltpac2500 and a Plasma 50amp both JUNK=LOTOS
the ltpac lasted a few weeks then smoke came out when i had it on but wasn't using it. the plasma cutter never worked for one second. just had it hitched
Categories: All Feeds, TIG Welding
Miller Plasma Cutter Part 2
This is Part 2 of Using a Spectrum 625 Xtreme Miller Plasma Cutter
Categories: All Feeds, TIG Welding
Metal Fabrication
Down and Dirty Metal Fabrication tips using a Precision Build Pro Welding Table
Categories: All Feeds, TIG Welding
Aluminum Welding of Small Castings
Cast Aluminum Welds like Fidos Butt - Aluminum Welding Tips for Small Cast parts
Categories: All Feeds, TIG Welding
TIG WELD WITHOUT DOOM
I want to weld 1mm SS with full tig weld. But once i weld the sheet dooms up. I want a answer for this that, how can i weld it fully without any doom in
Categories: All Feeds, TIG Welding
Setting a Miller HF Dialarc to weld aluminum
First of all when I got out of high school I welded aluminum for 10 years.Tig and mig.Got pretty good at it. They made me a welding foreman and I would
Categories: All Feeds, TIG Welding
Gas
What gas do you use to GMAW Stellite 21 to 316L stainless? --------------------------------------------------- I would probably use either trimix 90
Categories: All Feeds, TIG Welding
impossible aluminum setup?
I have a 1 to 2 aluminum weld joint with a 1/4 x 45' bevel. Final weld will fill the bevel and 1/4 fillet on top. Running a Miller 350 Syncrowave.
Categories: All Feeds, TIG Welding
old time welder
to restart a 7018 when the flux (not slag as you said it was)extends past the rod, just hold the rod in your hand and pinch it off with your thumb by pushing
Categories: All Feeds, TIG Welding
tip for salvaging stick electrodes
alot of times you accidentally chip alot of flux off the end of your electrode and end up just throwing it out to avoid porosity. what i found is that
Categories: All Feeds, TIG Welding
Tip for setting the right amperage
A good starting point for setting your amperage for stick welding is the amperage setting should be roughly the same as the decimal equivalent of the diameter
Categories: All Feeds, TIG Welding
Tip for welding with 7018.
My advise is when you are using 7018 and chipping the weld is to keep your mouth shut. I had to learn the hard way, when a dime size piece of very
Categories: All Feeds, TIG Welding
Getting started
I just bought a Hobart Mig welder. I know how to arc weld and use a gas torch, but I have never Mig welded. Which do I adjust first, wire feed, amperage,
Categories: All Feeds, TIG Welding
Help with 1/8 open root 2g single v bend test mig
Cant seem to figure out what to run the machine at.. fine on test plates and fill and cap but on my root wire hesitates and globs up. Also wondering about
Categories: All Feeds, TIG Welding
mig welding aluminum
1. Is it worth it to try to weld aluminum with a mig? 2. If it is will a 110 amp 240 v mig do the job? ----------------------------------------------------
Categories: All Feeds, TIG Welding
Pages
Golden Verse
| Romans 3:26 |
|---|
| for the showing, [I say], of his righteousness at this present season: that he might himself be just, and the justifier of him that hath faith in Jesus. |